Smart Factory Automation Using Internet of Things to Ensure Quality Manufacturing

Authors

  • Piyush Pariyumbud
  • Rohit Samkaria
  • Nitin Karnatak
  • Rajesh Singh
  • Anita Gehlot
  • Sushabhan Choudhary

Keywords:

Industrial Automation, IoT, XBee, Arduino, l NodeMCU,

Abstract

There is this concern in most of the industries to lower the production cost and to increase the production along with insuring the safety of its employees. In this paper, IoT based smart factory automation has been introduced which would not just increase the efficiency of industries, but would also insure safety of the workers. And as it could be controlled from any place of the world with internet connectivity using a mobile application, it would decrease the human capital required to run an industry. It would assist with the controlling of the manufacturing processes, detection of the error in the system and controlling of the production rate in accordance with the consumer interest.

Cite this Article
Piyush Pariyumbud, Rohit Samkaria, Nitin Karnatak, et al. Smart Factory Automation using IoT to Ensure Quality Manufacturing. Research & Reviews: A
Journal of Embedded System & Applications. 2017; 5(3): 1–6p.

Author Biographies

  • Piyush Pariyumbud

    Department of Electronics, Instrumentation and Control, University of Petroleum and Energy Studies,
    Dehradun, India.

  • Rohit Samkaria

    Department of Electronics, Instrumentation and Control, University of Petroleum and Energy Studies,
    Dehradun, India.

  • Nitin Karnatak

    Department of Electronics, Instrumentation and Control, University of Petroleum and Energy Studies,
    Dehradun, India.

  • Rajesh Singh

    Department of Electronics, Instrumentation and Control, University of Petroleum and Energy Studies,
    Dehradun, India.

  • Anita Gehlot

    Department of Electronics, Instrumentation and Control, University of Petroleum and Energy Studies,
    Dehradun, India.

  • Sushabhan Choudhary

    Department of Electronics, Instrumentation and Control, University of Petroleum and Energy Studies,
    Dehradun, India.

References

Wollschlaeger, Martin, ThiloSauter, and JuergenJasperneite. "The future of industrial communication: Automation networks in the era of the internet of things and industry 4.0." IEEE Industrial Electronics Magazine 11.1 (2017): 17-27.

Jung, Jieun, et al. "Design of Smart Factory Web Services Based on the Industrial Internet of Things." Proceedings of the 50th Hawaii International Conference on System Sciences. 2017.

Bi, Zhuming. "Embracing Internet of Things (IoT) and big data for industrial informatics." (2017): 949-951.

Fuhr, Peter L., et al. "Convergence and Commercial Momentum-Industrial Internet of Things Evolution." InTech 2017.2 (2017).

Hu, Bin, et al. "Co-design of Safe and Efficient Networked Control Systems in Factory Automation with State-dependent Wireless Fading Channels." arXiv preprint arXiv:1708.06468 (2017).

Lennvall, Tomas, Mikael Gidlund, and Johan Åkerberg. "Challenges when bringing IoT into industrial automation." AFRICON, 2017 IEEE. IEEE, 2017.

Hwang, Gyusun, et al. "Developing performance measurement system for Internet of Things and smart factory environment." International Journal of Production Research 55.9 (2017): 2590-2602.

Choudhry, Varchas, Rajesh Singh, and Anita Gehlot. "RSSI-Based Indoor Robot Localization System Using LabVIEW." Proceeding of International Conference on Intelligent Communication, Control and Devices. Springer Singapore, 2017.

Gehlot, Anita, Rajesh Singh, Rohit Samkaria, and Sushabhan Choudhury. "WPAN and PSO based Water Quality Monitoring with LabVIEW as data logger." International Journal of Engineering and Technology (IJET) 7, no. 5 (2015).

Agarwal, Ateev, et al. "WPAN Based Cattle Health Monitoring With Labview as A Data Logger." International Journal of Future Generation Communication and Networking 9.6 (2016): 274-284.

Downloads

Published

2018-02-08

Issue

Vol. 5 No. 3 (2017)

Section

Articles

License

Declaration and Copyright Transfer Form

(to be completed by authors)

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

  • I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.
  • I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).
  • I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.
  •  I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. ________________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.